electric box fixture screws too wide

2024-11-23T10:25:50 | By china cnc mechanical parts suppliers , DOD blog

electric box fixture screws too wide What always blew my mind was when a heavy fixture (maybe 30+ lbs) came out to the job and the mounting screws were (2) 8-32. On the . Closed junction box for the connection of cables in indoor and protected outdoor areas. Rectangular design without entries. Suitable for wall and ceiling mounting, on mounting panels and threads in the floor.

0 · junction box
1 · electrical
2 · Old electric box won't fit new ceiling fan mounting
3 · New light fixture doesn't fit on junction box : r/electricians
4 · Light fixture mounting screws too long : r/electrical
5 · Junction box wrong shape/size for light
6 · Electrical box too narrow for new light fixture : r/DIY
7 · Any tricks for Old Work Box opening that's too large?

I tested the Travelisimo Electric Lunch Box and it's a game changer for my on-the-go meals! Keep your food hot and tasty wherever you go. Available now!

The other solution is to not tighten the mounting plate up against the recessed box. Loosen the screws that hold it to the box so it hangs below . Took old fan down and new fan mounting bracket is about a quarter to a half inch too wide for the box. Electric box screw hole to screw hole is 2.75 inches. New bracket has to have screws be at least a little more than 3 .

I bought a new LED light fixture to replace an old basic lamp holder. After I opened everything up, I realized the screw holes in the box are spaced 2-3/4" apart, but the fixture requires 3-1/2". . What always blew my mind was when a heavy fixture (maybe 30+ lbs) came out to the job and the mounting screws were (2) 8-32. On the .The fixture mounting screws are toward the outside of the mounting bracket and ceiling drywall is right above them. When I screw the caps on to keep the fixture mounted it hangs from the . Sheetrocker cut the hole too big on an old work box opening, and the tabs aren't catching. Any neat tricks or "gadgets" to fix this issue - short of cutting out the rock and patching in a new piece with a proper sized cut out?

I’m trying to install a new light fixture, and was able to mount the included T-piece to the box, but the screws that are supposed to attach the fixture to the T-piece are hitting the .

After making your connections to the switch, wrap two or three wraps of electrical tape around the switch and secure it into the box. You can also replace the existing box with a .

The other solution is to not tighten the mounting plate up against the recessed box. Loosen the screws that hold it to the box so it hangs below the box enough for the other screws to be usable. It may take some fiddling with fixture screws to find just the right setting. Now I'm trying to install the mounting bracket for the light fixture and it is too wide for these boxes. The outer screws which must go in the outer holes are touching the plastic of the box itself. Took old fan down and new fan mounting bracket is about a quarter to a half inch too wide for the box. Electric box screw hole to screw hole is 2.75 inches. New bracket has to have screws be at least a little more than 3 inches apart.

I bought a new LED light fixture to replace an old basic lamp holder. After I opened everything up, I realized the screw holes in the box are spaced 2-3/4" apart, but the fixture requires 3-1/2". The screws for the new fixture also seem to be slightly bigger as well. What always blew my mind was when a heavy fixture (maybe 30+ lbs) came out to the job and the mounting screws were (2) 8-32. On the heaviest (say 40-50 lbs and over), the manufacturer added a cable that was supposed to be attached directly to the electrical box.

You need to acquire a light fixture mounting bracket. The type that you need would look like the bracket as shown in the picture below: Install it through the longer slotted holes into the existing electrical box holes. You can use the screws from the old light fixture.

The fixture mounting screws are toward the outside of the mounting bracket and ceiling drywall is right above them. When I screw the caps on to keep the fixture mounted it hangs from the ceiling rather than being flush. Do I need to cut the drywall or just let the screws push in? Sheetrocker cut the hole too big on an old work box opening, and the tabs aren't catching. Any neat tricks or "gadgets" to fix this issue - short of cutting out the rock and patching in a new piece with a proper sized cut out?

junction box

Took old fan down and new fan mounting bracket is about a quarter to a half inch too wide for the box. Electric box screw hole to screw hole is 2.75 inches. New bracket has to have screws be at least a little more than 3 inches apart. I bought a new LED light fixture to replace an old basic lamp holder. After I opened everything up, I realized the screw holes in the box are spaced 2-3/4" apart, but the fixture requires 3-1/2". The screws for the new fixture also seem to be slightly bigger as well. What always blew my mind was when a heavy fixture (maybe 30+ lbs) came out to the job and the mounting screws were (2) 8-32. On the heaviest (say 40-50 lbs and over), the manufacturer added a cable that was supposed to be attached directly to the electrical box. You need to acquire a light fixture mounting bracket. The type that you need would look like the bracket as shown in the picture below: Install it through the longer slotted holes into the existing electrical box holes. You can use the screws from the old light fixture.

Install the 8/32 screws in the bracket that hold the light fixture. Cut them to length if necessary. Mount the bar to the box using 6/32 flat head screws, same as on a switch or receptacle. Swivel the bracket to vertical and install the light. If the 8/32 are too long, they hit the 6/32 and box so get the the length on the 8/32 first. I removed our old broken fan, but found that the new mounting bracket is too wide for the electrical box mounting holes. They are less than 2.75" wide. My bracket has slots for variable mounting widths, but it is too tight to mount the screws straight. The fixture mounting screws are toward the outside of the mounting bracket and ceiling drywall is right above them. When I screw the caps on to keep the fixture mounted it hangs from the ceiling rather than being flush. Do I need to cut the drywall or just let the screws push in?

junction box